Design of switchable band‐notched frequency selective absorber

An active band‐notched frequency selective absorber (BNFSA) with switchable notch band is proposed in this article. The BNFSA is a two‐layer structure composed of a lossy layer at the top and a ground plane at the bottom, separated by an air spacer. The element of the lossy layer is a lumped‐resistor‐loaded metallic dipole with a parallel LC resonance structure, which is realized by complementary n‐shaped resonator (CnR) inserted in the center, and PIN diode is welded at two arms of CnR. The bias circuit printed on the back of the substrate of the lossy layer connects to anode and cathode of the diode by via hole and isolates by the inductor. Simulation results show that the notch bands are located at 4.50 and 6.81 GHz when the diode sets to ON and OFF, respectively. To validate the performance of switchable BNFSA, the prototypes are fabricated and measured, reasonable agreement between simulated and measured results is obtained.     

A solution to measure traveler’s transfer tolerance for walking mode and dockless bike-sharing mode

The Journal of Supercomputing - Dockless bike-sharing is more and more popular all over the world, which enables passengers to choose destinations more flexibly, so that the transfer radius between...     

Catastrophic Evolution of Water Inrush from A Water-Rich Fault in Front of Roadway Development: A Case Study of The Hongcai Coal Mine

Mine Water and the Environment - A fault can be both the inrush channel and the water source. In order to better understand how such a mine disaster develops, a fluid–solid coupling analysis...     

基于模糊综合评判和层次分析法的中子管故障风险评估

中子管是一种用途广泛的关键部件，然而目前国产中子管的可靠性水平与国外相比还有一定差距，难以满足各行业的使用需求。本文分析了中子管的主要故障模式，采用模糊综合评判和层次分析法对中子管故障进行了多级模糊综合评判，并对中子管故障风险进行了评估。结果表明，中子管总体故障风险水平中等，故障风险前3位的部件为靶、氘氚储存器和加速极，在设计和使用中应重点关注靶释放氦气，靶膜氧化，氘氚储存器吸气剂局部破损，绝缘瓷管破损，加速极离子加速、聚焦不稳定等故障。     

基于学习进程的学习评估在大学化学教学中的实践

高等教育质量提升的关键在于课程教学质量的不断完善。作为高等教育的重要环节,化学课程教学在非化学化工专业人才的知识体系构建、能力培养、素质养成方面有着不可或缺的作用。大学化学课程的教学实践表明,基于学习进程的评估有利于激发学生的学习积极性,显著提高教学班的整体成绩并实现课程教学质量的提升。     

ZIF衍生多孔碳纳米纤维用于高效电容去离子的研究

作为一种环保节能的新兴脱盐技术，电容去离子技术正在成为替代反渗透脱盐和电渗析脱盐的一项重要的脱盐技术。各种碳基材料被广泛地应用于电容去离子电极材料的研究，然而大多数碳基材料为粉末状材料，需要添加黏结剂，这必将导致电极材料电吸附能力的下降。利用静电纺丝技术，将ZIF纳米颗粒和聚丙烯腈混纺，并通过分段高温热处理过程，成功合成了具有柔性结构的整体性多孔碳纳米纤维。由于其具有孔道结构的分级分布和较强的亲水性等优良特性，所制得的多孔碳纳米纤维在1.2 V电压下于500 mg/L NaCl溶液中表现出良好的电吸附性能，脱盐量达到了19.92 mg/g，比普通碳纳米纤维提高了一倍以上。     

白炭黑表面改性研究现状及进展

白炭黑是橡胶工业中非常重要的补强剂,目前市场上主要是采用沉淀法进行生产。但沉淀法生产的白炭黑直接应用时效果较差,在工业应用前大多需要进行改性处理。通过分析国内外白炭黑改性技术研究现状,归纳总结出了表面接枝改性、偶联剂改性、离子液改性、大分子界面改性及并用改性5种白炭黑改性技术的特点,其中偶联剂改性为目前工业应用上的主要改性工艺,而其他改性工艺由于生产成本、改性效果、产品稳定性等因素暂未实现大规模工业应用。     

Direct coagulation casting of silicon carbide suspension via polyelectrolyte dispersant crosslink reaction

A direct coagulation casting method for silicon carbide ceramic suspension using dispersant crosslink reaction is reported. Polymer electrolyte (polyethyleneimine, PEI) was used as dispersant to prepare silicon carbide suspension. Common food additives (carboxymethyl cellulose, CMC) were used to coagulate the electrosteric stabilized silicon carbide suspension. There was a well disperse silicon carbide suspension with 0.2 wt% PEI at pH = 5-6. Influence of coagulant on viscosity and zeta potential of the silicon carbide suspension was investigated. It indicates that the high solid loading silicon carbide suspension can be destabilized and coagulated at elevated temperature. It can be attribute to the gradual decrease of electrosteric force due to the crosslink reaction between PEI and CMC. Silicon carbide wet green body with compressive strength of 1.99 MPa could be demolded at 70°C which is higher than that prepared by traditional DCC and dispersant reaction method for nonoxide ceramics. Dense silicon carbide ceramics with relative density above 98.8% and 99.3% had been prepared by liquid phase pressureless and hot pressed sintering, respectively.     

轧制与退火对T9S钛合金板材组织与性能的影响

研究了轧制变形量及退火温度对T9S钛合金板材显微组织和室温力学性能的影响。结果表明:增加成品轧制变形量,板材组织破碎更充分,退火后形成等轴α相、拉长α相和晶间β相组织形貌,变形流线比较明显,板材室温强度和硬度升高,伸长率降低,弹性模量增加。随着退火温度升高,板材室温强度和硬度逐渐降低,伸长率逐渐提高,横向弹性模量逐渐减小,纵向弹性模量先增加后减小。经(750~790) ℃×45 min空冷退火处理后的板材可以获得较好的强度和塑性的匹配。